Showing results: 661 - 675 of 1660 items found.
-
XXL+ -
Atlas Material Testing Technology
The Atlas SUNTEST XXL+ is a large xenon lamp weathering and lightfastness test chamber meeting various ISO, ASTM, and ICH industry standards. Its horizontal 3000 cm2 exposure area is best-in-class for 3-D specimen testing.
-
Kikusui Electronics Corp.
complied standards and features of the KHA1000 (dedicated for single phase), is equipped for the harmonic and flicker compliance test exceeding 16A of the single-phase and three-phase equipment. With this unit alone, you can take highly accurate simultaneous three-phase measurements up to 40A/phase*.
-
RapidTrace 700 -
Vonaq Ltd
Compact, Powerful and Easy to use. This high performance low cost LAN Tester / Wiremap Tester and Cable Fault Locator is the perfect tool to enable you to test and certify structured cabling continuity to TIA568A/B, USOC and ISDN standards.
-
JTAG Technologies Inc.
The JTAG Live Controller is USB connected and powered and features a single test access port in JTAG Technologies standard 10-way IDC pin-out. The JTAG Live controller is a smart, low-cost and easy-to-use USB JTAG/Boundary-scan interface.
-
YQA Series -
Jinan Testing Equipment IE Corporation
This kind of machine is designed according to the International standards EN 10263-1:2001 “Metallic materials upset test methods”, especially for the quality inspection of high-speed rods and wires. Through simulating the quick press conditions of the metallic materials during the upset and pressing, the machine truthfully reflects the instances of the quickly compressed rods and wires. This kind of machine is widely used in the steel industry, standard samples manufacturing industry, and tools manufacturing industry, for the inspection of the metallic materials upset tests. Under the room temperature or the hot conditions, exert test force on the direction of specimen axial line, quickly compress the specimen, and then inspect the metal ability of bearing upset deformation in the specified upset ratio. It also can show the metal surface disfigurements.
-
WDT-1 -
Lisun Electronics Inc.
This equipment is designed and manufactured according to corresponding regulation in standard IEC884-1, GB299.1-96, GB16915.1-97 and other electronic accessories relevant standard. Mainly used to test damage degree of fixed connection components lead wire of with thread clamping type and no screw terminals, so as to inspect whether it can withstand mechanical stress during normal use.Specification: • Power supply: AC220V 50Hz • Test rate: 10±2r/min (GB16915.1-97: 12 ±1r/min) • Rotating radius: 100mm • Test distance: 250~500mm adjustable • Test numbers (Number of rotating): 0~999999 any set • Mass: 0.3KG, 0.4KG, 0.7KG, 0.9KG, 1.4KG, and 2.0KG (GB16915.1-97: 30N, 40N, 50N, 60N each of 2 pcs) • Stations: 2 • Dimension: 1200×1400×400 (mm) • Remarks: The mass and rotating radius can be optional as per customer requirements.
-
Tequra Analytics -
Simplicity AI Ltd
Tequra Analytics is a test data management and analysis solution for advanced manufacturing organisations. By using the tools provided by Tequra Analytics an extensive insight into manufacturing can be gained, enabling actions to be taken to improve quality and streamline processes. ATML Results - Industry standard format for automated test. CSV Output - Machine readable, open in spreadsheet software. PDF Reports.
-
GDJB-PC6 -
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
1.This tester with standard 6 phase voltage, 6 phase current output,2.Voltage 125V/phase, current 30A/phase, 6 phases in parallel can up to 180A.3.Digital Signal Processor Microcomputer.4.Not only test the traditional relays and protectors, but also test the modern micro computer replays, special for transformer differential protection and transfer equipments.
-
Insight Scientific
This is the fully automatic semiconductor probe assembly and test equipment. It features ultra high precision in assembly process and the intelligent inspection of the finished products. This product is one of the most technologically advanced equipment by international standards in this industry and been exported to North America.Key Features: ● Assembly Precision:15um ● UPH:720 ● Visual Inspection included ● Spring Force Test
-
MTI Corp.
economic nail penetration tester for all types of rechargeable batteries, which meets CE standard. The nail penetration is performed inside a safe and vented stainless-steel test chamber using a 3~8 mm diameter steel nail at variable speed from 10~100mm/s. There is a fixture to tighten various type cells, pouches or cylinders in the test chamber.
-
Shenzhen Chuangxin Instruments Co., Ltd.
The CX2672C is a high-precision testing device with upper limited alarm function for withstand voltage test. And it's is strictly designed according to the related IEC standard. The voltage, current and timing are with digital display function. The testing is quick and high accuracy which is not only applied in the production line but also in the lab. It's a neccessary tester for electric safety test of electrical equipment.
-
HT Italia Srl
SOLAR-515w allows both testing a single-phase (three-phase with optional MPP300) photovoltaic system and verifying I-V curve. Thanks to remote unit SOLAR02, it is possible to test the system complying with the requirement of simultaneity as provided for by the reference standard. SOLAR02 is a datalogger which, synchronized with SOLAR-515w, acquires the data relevant to irradiation and temperature while tests carried out by SOLAR-515w are carried out.
-
OTM 1000 -
OmniTek
The system provides high precision waveform, vectorscope and gamut displays; real-time picture monitor; comprehensive SDI input status information; audio monitoring capabilities; and SDI physical layer analysis including eye-pattern and jitter displays. The OTM 1000 also contains an optional test signal generator, providing a full range of standard test patterns and zone plates.
-
York EMC Services Ltd
The Harmonics & Flicker Generator (HFG01) has been designed for the purpose of verifying harmonic and flicker test equipment. It provides an easy and reliable way to externally check the performance of the measurement system to the EN/IEC 61000-3-2 harmonics and EN/IEC 61000-3-3 flicker standards; particularly important as these tests rely on software control and calculation, and for which there is no intuitive sense of the response.
-
SCHILLER AUTOMATION GmbH & Co. KG
HDMI test adapters and test fixture kits facilitate Source and Sink compliance testing and HDMI cable testing. Our products are used in Certification Testing to CEA 1.3b, 1.4a, 2.0 and 2.1 standards. 1080p and 4K formats are supported. We offer A and D style plug and receptacle connectors, male and female SMA leads, with and without HEAC channels.